Dean came to our studio, want to own the 2004 350Z convertible models become more powerful, more full braking force because he wanted his car fast enough and stable enough. The face of such a simple task, we of course said no problems. But Dean had another request, he wants us to finish the work within two weeks, time is really becoming very nervous, but we still accepted the challenge and this task is named JWT 350ZTT Garrett ball bearing turbocharger produced and two in the cold, has a powerful driving stability, like the famous magazine modified almost comparable to the original product. Intentions exhaust kit because its performance and exhaust sound for the perfect being we have chosen to integrate with the twin turbo kit complete.
Fast Intentions exhaust
modified car will be substantial increase in the maximum power ,UGG boots clearance, but also has a broad, flat torque curve of the peak, so we use RPS lightweight flywheel unit with the same limit from the RPS Street Clutch Kit to control the transmission power to ensure the power can be solved with out a huge to the impact of the car as much as possible to maintain smooth driving stability.
flywheel and clutch
have the ability to run very fast car also means you will soon need to have the ability to stop the car, which sets 2004 350Z convertible models of the original brake systems are now overwhelmed, so we need to be able to quickly put on the brake the car braking system, and for well-known manufacturers StopTech 350Z launch, the diameter increased to 332mm front disc brakes front and rear brake kit fits requirements.
above all the necessary components are ready, we commenced the.
first day of the installation:
the first day of installation to do the most work but is demolition, first of all, engine coolant and engine oil must be released. To install the turbo package, many components on the car must be removed down, like the engine hatch, cooling water tank, intake air box, front bumper, water tank water, cooling water bypass pipe, generator, starter, exhaust system, driveshaft, transmission, clutch, flywheel and exhaust manifold, etc., which need to be removed.
because the engine construction, so the engine compartment components are to be pulled around the removed parts
best installed separately, to prevent small parts missing something
dismantled many, and many a lot of
remove the drive shaft < br> and then removed to the middle of the exhaust is removed
gearbox is exposed after it is removed
clutch gearbox
in the transmission removed, we found that some of its oil, after the end of the block and oil pan seals are a bit broken, so we carry out repairs. In addition the existing use of space for the new turbo exhaust manifold is too tight, so was the original exhaust manifold pins removed, and shortened some of the installation of new exhaust manifold for the position of leaving.
next day installation:
work the next day to begin the conversion of the whole vehicle and install the modified parts. turbine oil circuit to be installed first up, the original sump oil pan because of the new added loop were modified turbine oil.
increase in the original oil pan on the right side of the turbine exhaust manifold oil circuit interfaces
After installation of the dual effect of
JWT turbo kit inside a pretty good set of performance exhaust manifold, is produced by JWT own design. The purpose of this manifold design is the pursuit of higher than the original flow manifold , and the full size design for this turbine, installed after the match exactly, although the reserved space is small, but the location was just right after installation.
left side exhaust manifold for the spark plug after installation when the effect of
found in the valve chamber cover problems,cheap UGG boots, had to replace the
removed the original spark plug in our numbers into a lower, which is more oil. if spark plug or ignition line will cause the oil to stick to the ignition failure, but because of the spark plug of the sealing ring is fixed in the valve chamber cover, and can not be replaced individually, so we decided to driver side, which is on the left side of the cylinder The valve chamber cover the entire replaced. looks like the spark plug holes inside the seal ring when there is a problem in the factory, because the components used in the normal course of aging or does not so easily damaged.
because the right side into the manifold mounting screws too long, may have affected turbine installation, so we cut this short root of the screw, brass nut that is installed on the third day
:
third day of work is mainly based on JWT's sports two 530 ball bearing turbo to set the oil and cooling water, when completed, will install the turbine on the exhaust manifold.
right side of the turbine in place, we will find a short cut really screw Flanagan important, otherwise the turbine installation will be seriously affected
left in place after the effect of the turbine, a larger space
side of the left and right side are already in place
turbine when the turbine to the exhaust manifold on a fixed time , you need to turbo exhaust side of the plane is slightly twisted to the point near the center line of the car, so you can ensure that the exhaust pipe can be installed on smoothly and will not distort because of the stress in the future impact on the frame structure.
then removed the original parts back in place, and put a new brake system, thus, have all the hardware installed on the end, but the car has not really finished,UGG shoes, waiting for us is fine tuned and exciting work.
Here, we look at the way for everyone to enjoy the few pictures turbo package, relative to domestic fans, friends often see different single turbine, which is a very complete all relevant parts of products, and Excellent work is not an ordinary:
arrived, it is the way several boxes, transit has not been any damage to the
have detailed instructions on the packaging,Discount UGG boots, and two Twin Turbo sticker
various types have been set by hardware package
turbine body, a large snail ah good ........< br> MADE IN JAPAN
V-type in the cold, so In fact, the two are separate, but through the middle of the air outlet port is connected to the intake manifold
package that already have a set of high flow mushroom head
already forming line, because it is specially designed Therefore, it is very easy package to install pipeline installation required
silicone tube has also been included in the package in the
cooling tubing, as well as supporting the vacuum tube has, the relevant connections are also prepared all the. To get these small things all their own is also very laborious
JWT = Jim Wolf Technology
more articles:
beautiful experience of love modified modified version of the Tiida car modification market ahead of Beijing.
No comments:
Post a Comment